Make your hydraulic hoses on site instead of waiting for them. The container arrives fully equipped, is set down, plugged in and starts producing. A continuous bench runs along one wall: the PARKER Parkrimp 2 crimper first, at the door end, then the PTS station, and the saw at the far end, against the rotating-tray rack that holds the hose coils. The hose is unrolled in a V-trough along a tape measure whose zero is on the saw blade. Opposite: the fittings, one bay per standard.
At the entrance, a clear area with waste bin, broom, fire extinguisher and first-aid kit; the crimping chart is posted on the inside of the door. The container connects to the site mains or to a generator through its external three-phase 400 V 32 A socket. Its long sides carry the customer’s livery: on the model, an example livery with a fictitious company and logo.
Ready to travel: everything is secured. Benches, shelving and equipment are bolted to the floor, walls or ceiling; the crimper is screwed to the bench and bins are held on the shelves by retaining bars or straps. Nothing moves during transport and handling.
PARKER fittings are one-piece: the ferrule is pre-crimped onto the fitting. With No-Skive technology there is no need to skive the hose, so no skiving machine is needed — saving time and equipment. They are stored by standard, one bay each: ORFS, JIC, DIN, BSP, NPT and SAE flanges.
Twenty feet is the format that moves with the site and loads onto a single truck. The model below is of an actual build: rotate it, open the doors, make the walls transparent.
A hydraulic hose always fails at the worst moment, and the costly question is not how to remake it: it is knowing which one to remake. PTS answers that question. Every hose assembled in the container gets a label carrying a unique number, applied at assembly and made to last in a hydraulic environment, in the sun and in the dust.
Beyond breakdown repairs, PTS gives you the real hose inventory: how many hoses on which machine, which ones have already been replaced twice, which ones are nearing the end of their service life. That is where preventive maintenance becomes possible. The software is supplied; only the printer, the scanner and the consumables need to be budgeted.
Internal dimensions in millimetres. Standard 20-foot container: 5,900 × 2,350 × 2,390 mm inside, 6,058 × 2,438 × 2,591 mm outside. One-metre clear entrance on the shelving side; on the bench side, 1,050 mm clear between the door and the crimper, electrical panel kept clear. Clear aisle of about 1,150 mm between the V-trough and the shelving. The tape measure starts at the blade (0) and increases towards the doors, over 3 m.
| Qty | Description |
|---|---|
| 1 | 20-foot container, preferably one-trip, aluminium tread-plate floor and welded fixing plates |
| 1 | Insulation: thin sprayed cork, or 30 mm sandwich panels where the climate calls for it |
| 1 | PARKER Parkrimp 2 crimper (83CE-083U): horizontal power unit, vertical motor, tilted head under a yellow guard, at the very end of the bench by the door, with one metre clear in front of it for crimping |
| 1 | Die sets on a tray under the bench, directly below the crimper |
| 1 | Hose cutting saw, at the end of the bench, against the rotating-tray rack |
| 1 | Fume extractor, 1,000 m³/h: fan on a stainless-steel bracket, black arm and hood above the saw |
| 1 | Tankless wall compressor, 160 l/min at 8 bar, and ABAC wall-mounted compressed-air hose reel with blow gun |
| 1 | Continuous steel assembly bench with wooden top, 600 kg rated, about 3.80 m long, from the crimper to the rotating-tray rack; it stops one metre short of the door, leaving room to crimp and keeping the electrical panel clear |
| 1 | V-trough along the front edge of the bench, 3 m tape measure with its zero on the saw blade: unroll the hose in the trough to the required length, mark, cut |
| 1 | 125 mm bench vice, fixed to the bench between the PTS station and the saw |
| 1 | Power tools: angle grinder, cordless drill, batteries and charger, stored under the bench on the lower shelf |
| 1 | PTS station: 15″ laptop, Zebra label printer and barcode scanner |
| 1 | 7-tray rotating rack in the back corner, one hose coil per tray, from small to large diameter |
| 6 | Bin shelving bays for fittings, one per standard (ORFS, JIC, DIN, BSP, NPT, SAE flanges), labelled bins |
| 1 | ParkerStore workshop stool |
| 1 | Customer livery on the long sides (example on the model, fictitious logo) and ParkerStore Onsite Solutions logo |
| 1 | Clear entrance area: 60 l waste bin, small oily-waste bin, broom, brush and dustpan on a wall bracket |
| 1 | Wall-mounted fire extinguisher with signage, first-aid kit |
| 1 | PARKER crimping chart (die selection by fitting and hose series), posted on the door |
| 1 | Hose internal cleaning station, used before crimping |
| 1 | Complete electrics: external 400 V supply through a Hypra 32 A socket in an enclosure below the panel, 220 V sockets, LED light fittings |
| 2 | Ceiling cable trays: electrics on one side, compressed-air network on the other |
This container is a starting point, not a closed catalogue. The layout is reworked around your machines, your hoses and the space you have.
Tell us which machines you maintain and where the container needs to go: we will come back with a layout and a price.
Samuel Creiche · CREISCENDO · creiscendo@creiscendo.com · +33 6 76 18 78 74
© CREISCENDO 2026 · 11 rue Nationale, 37150 Chisseaux, France · creiscendo@creiscendo.com · +33 6 76 18 78 74 · en.creiscendo.com